EdgeOS » Historique » Version 23
« Précédent -
Version 23/31
(diff) -
Suivant » -
Version actuelle
Christian Frabel, 04/01/2023 17:04
EdgeOS¶
ES-48-Lite EdgeOS 1.7.3
Documentation¶
https://dl.ubnt.com/guides/edgemax/EdgeOS_UG.pdf
https://dl.ubnt.com/guides/edgemax/EdgeSwitch_CLI_Command_Reference_UG.pdf
Commandes¶
(UBNT EdgeSwitch) #show mac-addr-table VLAN ID MAC Address Interface IfIndex Status ------- ------------------ --------------------- ------- ------------ 1 00:01:E8:8B:4F:CF 0/49 49 Learned 1 00:08:7C:3C:29:03 0/49 49 Learned 128 9C:B6:54:06:7E:56 0/5 5 Learned ...
show interfaces status all Port Name State Mode Status Type Status --------- ---------------------------- ------ ---------- ---------- ------------------ ------------ 0/1 Down Auto Unknown Inactive 0/2 Down Auto Unknown Inactive 0/3 Up Auto 100 Full Unknown Active ... (UBNT EdgeSwitch) #show interfaces switchport Port: 0/1 VLAN Membership Mode: General Access Mode VLAN: 1 (default) General Mode PVID: 3131 General Mode Ingress Filtering: Disabled General Mode Acceptable Frame Type: Admit all General Mode Dynamically Added VLANs: General Mode Untagged VLANs: 3131 General Mode Tagged VLANs: 3199 General Mode Forbidden VLANs: 1,20,128,376,3132,3166,3175 Trunking Mode Native VLAN: 1 (default) Trunking Mode Native VLAN tagging: Disable Trunking Mode VLANs Enabled: All Protected Port: False Port: 0/2 ...
(UBNT EdgeSwitch) #show fiber-ports optics-info all Link Link Nominal Length Length Bit 50um 62.5um Rate Port Vendor Name [m] [m] Serial Number Part Number [Mbps] Rev Compliance -------- ---------------- --- ---- ---------------- ---------------- ----- ---- ---------------- 0/49 OEM 0 0 SG35E40803862 SFP+10GSMD3120LC 10300 A 10GBase-LR 0/50 OPTIC 0 0 STC03051500015 OPTICSFP+10GCP3M 10300 A0 DAC (UBNT EdgeSwitch) #show fiber-ports optics all Output Input Port Temp Voltage Current Power Power TX LOS [C] [Volt] [mA] [dBm] [dBm] Fault -------- ---- ------- ------- ------- ------- ----- --- 0/49 45.2 3.332 31.5 -3.079 -3.223 No No 0/50 N/A N/A N/A N/A N/A N/A N/A Temp - Internally measured transceiver temperatures. Voltage - Internally measured supply voltage. Current - Measured TX bias current. Output Power - Measured optical output power relative to 1mW. Input Power - Measured optical power received relative to 1mW. TX Fault - Transmitter fault. LOS - Loss of signal.
Allumer un port et remplir sa description¶
(UBNT EdgeSwitch) #conf (UBNT EdgeSwitch) (Config)#interface 0/33 (UBNT EdgeSwitch) (Interface 0/33)#no shutdown (UBNT EdgeSwitch) (Interface 0/33)#description gentilserveur (UBNT EdgeSwitch) (Interface 0/33)#exit (UBNT EdgeSwitch) #write memory This operation may take a few minutes. Management interfaces will not be available during this time. Are you sure you want to save? (y/n) y Config file 'startup-config' created successfully . Configuration Saved!
(UBNT EdgeSwitch) #write memory This operation may take a few minutes. Management interfaces will not be available during this time. Are you sure you want to save? (y/n) y Config file 'startup-config' created successfully . Configuration Saved!
(UBNT EdgeSwitch) #conf (UBNT EdgeSwitch) (Config)#interface 0/35 (UBNT EdgeSwitch) (Interface 0/35)#shut (UBNT EdgeSwitch) (Interface 0/35)#do write memory This operation may take a few minutes. Management interfaces will not be available during this time. Are you sure you want to save? (y/n) y Config file 'startup-config' created successfully . Configuration Saved! (UBNT EdgeSwitch) (Interface 0/35)#
(UBNT EdgeSwitch) (Config)#interface 0/12-0/15 (UBNT EdgeSwitch) (Interface 0/12-0/15)#shut
(s58) #copy nvram:startup-config tftp://192.168.3.19/s58 Mode........................................... TFTP Set Server IP.................................. 192.168.3.19 Path........................................... ./ Filename....................................... s58 Data Type...................................... Text Configuration Management access will be blocked for the duration of the transfer Are you sure you want to start? (y/n) y File transfer operation completed successfully. (s58) #
Exemple¶
À titre d'exemple, activons le port 1 du switch s54 localisé à Picto afin d'y connecter un dispositif. On peut se connecter au switch de diverses façons, cependant à distance, on peut se connecter d'abord sur nagios.tetaneutral.net et, de là, atteindre s54. Ceci nécessite d'avoir sa clef sur nagios afin de permettre la connexion ssh. * ssh -lroot -p2222 nagios.tetaneutral.net * Connexion à s54 passwd: ubnt ssh ubnt@s54 Après connexion au switch, on passe en root pw: ubnt enable On passe ensuite en mode config conf Pour la config du port 1 interface 0/1 On active le port no shut On revient en mode config général exit Puis on sort du mode config exit Il faut encore sauver la config dans une mémoire permanente write mem La configuration est terminée