{{>toc}}

h1. EdgeOS

ES-48-Lite EdgeOS 1.7.3

h2. Documentation

https://dl.ubnt.com/guides/edgemax/EdgeOS_UG.pdf

https://dl.ubnt.com/guides/edgemax/EdgeSwitch_CLI_Command_Reference_UG.pdf

h2. Commandes

<pre>

(UBNT EdgeSwitch) #show mac-addr-table 

VLAN ID  MAC Address         Interface              IfIndex  Status

-------  ------------------  ---------------------  -------  ------------

1        00:01:E8:8B:4F:CF   0/49                   49       Learned

1        00:08:7C:3C:29:03   0/49                   49       Learned

128      9C:B6:54:06:7E:56   0/5                    5        Learned

...

</pre>

<pre>

show interfaces status all

Port       Name                          State   Mode        Status      Type                Status

---------  ----------------------------  ------  ----------  ----------  ------------------  ------------

0/1                                      Down    Auto                    Unknown             Inactive

0/2                                      Down    Auto                    Unknown             Inactive

0/3                                      Up      Auto        100 Full    Unknown             Active

...

(UBNT EdgeSwitch) #show interfaces switchport

Port: 0/1

VLAN Membership Mode: General

Access Mode VLAN: 1 (default)

General Mode PVID: 3131

General Mode Ingress Filtering: Disabled

General Mode Acceptable Frame Type: Admit all

General Mode Dynamically Added VLANs:

General Mode Untagged VLANs: 3131

General Mode Tagged VLANs: 3199

General Mode Forbidden VLANs: 1,20,128,376,3132,3166,3175

Trunking Mode Native VLAN: 1 (default)

Trunking Mode Native VLAN tagging: Disable

Trunking Mode VLANs Enabled: All

Protected Port: False

Port: 0/2

...

</pre>

<pre>

(UBNT EdgeSwitch) #show fiber-ports optics-info all

                         Link Link                                 Nominal

                       Length Length                                   Bit

                         50um 62.5um                                  Rate

Port     Vendor Name      [m] [m]  Serial Number    Part Number     [Mbps] Rev  Compliance

-------- ---------------- --- ---- ---------------- ---------------- ----- ---- ----------------

0/49     OEM              0   0    SG35E40803862    SFP+10GSMD3120LC 10300 A    10GBase-LR

0/50     OPTIC            0   0    STC03051500015   OPTICSFP+10GCP3M 10300 A0   DAC

(UBNT EdgeSwitch) #show fiber-ports optics all     

                                    Output    Input

Port      Temp  Voltage  Current     Power    Power   TX     LOS

           [C]   [Volt]     [mA]     [dBm]    [dBm]   Fault

--------  ----  -------  -------   -------  -------   -----  ---

0/49      45.2    3.332     31.5    -3.079   -3.223   No     No

0/50       N/A      N/A      N/A       N/A      N/A   N/A    N/A

 Temp - Internally measured transceiver temperatures.

 Voltage - Internally measured supply voltage.

 Current - Measured TX bias current.

 Output Power - Measured optical output power relative to 1mW.

 Input Power - Measured optical power received relative to 1mW.

 TX Fault - Transmitter fault.

 LOS - Loss of signal.

</pre>

h3. Allumer un port et remplir sa description

<pre>

(UBNT EdgeSwitch) #conf

(UBNT EdgeSwitch) (Config)#interface 0/33

(UBNT EdgeSwitch) (Interface 0/33)#no shutdown

(UBNT EdgeSwitch) (Interface 0/33)#description gentilserveur

(UBNT EdgeSwitch) (Interface 0/33)#exit

(UBNT EdgeSwitch) #write memory 

This operation may take a few minutes.

Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

</pre>

<pre>

(UBNT EdgeSwitch) #write memory         

This operation may take a few minutes.

Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

</pre>

<pre>

(UBNT EdgeSwitch) #conf

(UBNT EdgeSwitch) (Config)#interface 0/35

(UBNT EdgeSwitch) (Interface 0/35)#shut

(UBNT EdgeSwitch) (Interface 0/35)#do write memory

This operation may take a few minutes.

Management interfaces will not be available during this time.

Are you sure you want to save? (y/n) y

Config file 'startup-config' created successfully .

Configuration Saved!

(UBNT EdgeSwitch) (Interface 0/35)#

</pre>

<pre>

(UBNT EdgeSwitch) (Config)#interface 0/12-0/15

(UBNT EdgeSwitch) (Interface 0/12-0/15)#shut

</pre>

<pre>

(s58) #copy nvram:startup-config tftp://192.168.3.19/s58

Mode........................................... TFTP  

Set Server IP.................................. 192.168.3.19

Path........................................... ./

Filename....................................... s58

Data Type...................................... Text Configuration

Management access will be blocked for the duration of the transfer

Are you sure you want to start? (y/n) y

File transfer operation completed successfully.

(s58) #

</pre>

h2. Exemple

<pre>

À titre d'exemple, activons le port 1 du switch s54 localisé à Picto afin d'y connecter un dispositif.

On peut se connecter au switch de diverses façons, cependant à distance, on peut se connecter d'abord sur nagios.tetaneutral.net et, de là, atteindre s54.

Ceci nécessite d'avoir sa clef sur nagios afin de permettre la connexion ssh.

ssh -lroot -p2222 nagios.tetaneutral.net

Connexion à s54 passwd: ubnt

ssh ubnt@s54

Après connexion au switch, on passe en root pw: ubnt

enable

On passe ensuite en mode config

conf

Pour la config du port 1

interface 0/1

On active le port

no shut 

On revient en mode config général

exit

Puis on sort du mode config

exit

Il faut encore sauver la config dans une mémoire permanente

write mem

La configuration est terminée

</pre>